Filter
Top Products
918
FX3G/FX3U/FX3UC Series Programmable Controllers
Programming Manual - Basic & Applied Instruction Edition
B Instruction Execution Time
B-6 Execution Time on Combination of Applicable Devices and Indexing
Appendix B-6 Execution Time on Combination of Applicable Devices and
Indexing
In examples shown below for basic instructions, MOV instruction and data comparison instructions, the instruction
execution time varies depending on the combination of target devices and absence/presence of indexing.
The combinations of target devices marked with "*1" and "*2" are handled as exceptions because high speed
processing is adopted in the technique.
Appendix B-6-1 Basic instruction (LD/LDI/AND/ANI/OR/ORI) execution time
•FX3U/FX3UC PLCs
•FX
3G PLCs do not support indexing of bit devices and contact instructions with bit specification of word devices in
basic instructions.
Appendix B-6-2 Applied instruction execution time
1. MOV (FNC 12) instruction execution time
•FX3U/FX3UC PLCs
- MOV instruction (16-bit operation)
*1. These combinations are handled as exceptions because high speed processing is adopted in the technique.
*2. When the instruction is executed for a BFM in a special extension block/unit for FX
3U/FX3UC Series.
- DMOV instruction (32-bit instruction)
*1. These combinations are handled as exceptions because high speed processing is adopted in the technique.
*2. When the instruction is executed for a BFM in a special extension block/unit for FX
3U/FX3UC Series.
Specified device type Condition Instruction execution time
Bit device
Without indexing 0.065
With indexing 11.9
Word device Bit specification 8.8
Command
contact
S (source)
D (destination)
Without indexing (µs) With indexing (µs)
KnY,KnM,KnS T,C,D R
U\G
*2
KnY,KnM,KnS T,C,D R
U\G
*2
ON
KnX,KnY,KnM,KnS 15.5 12.1 13.8 212.9 18.6 16.6 16.9 214.7
T,C,D 12.1
0.64
*1
10.4 209.7 16.6 14.5 14.8 212.8
R 13.8 10.4 12.1 211.3 16.9 14.8 15.1 213.1
U\G
*2
131.8 128.5 130.2 377.9 133.1 129.9 131.5 379.4
K,H 12.5
0.64
*1
10.8 210.1 15.4 13.3 13.6 211.6
OFF
KnX,KnY,KnM,KnS
0.325
T,C,D
0.32
*1
R
U\G
*2
K,H
0.32
*1
Command
contact
S (source)
D (destination)
Without indexing (µs) With indexing (µs)
KnY,KnM,KnS T,C,D R
U\G
*2
KnY,KnM,KnS T,C,D R
U\G
*2
ON
KnX,KnY,KnM,KnS 15.5 12.4 13.8 311.1 18.7 17.0 17.1 313.0
T,C,D 12.4
1.48
*1
10.7 307.4 17.0 15.2 15.3 310.5
R 13.8 10.7 12.2 308.9 17.1 15.3 15.4 310.6
U\G
*2
199.8 195.9 197.4 542.6 201.2 197.3 198.8 544.0
K,H 13.0
1.48
*1
11.4 308.0 16.2 14.4 14.5 309.7
OFF
KnX,KnY,KnM,KnS
0.585
T,C,D
1.48
*1
R
U\G
*2
K,H
1.48
*1