Mitsubishi Electronics FX3G Video Gaming Accessories User Manual


 
711
FX3G/FX3U/FX3UC Series Programmable Controllers
Programming Manual - Basic & Applied Instruction Edition
33 Extension File Register Control – FNC290 to FNC299
33.1 FNC290 – LOADR / Load From ER
31
FNC275-FNC279
Data
Transfer 3
32
FNC280-FNC289
High Speed
Processing 2
33
FNC290-FNC299
Extension File
Register
34
FNC300-FNC305
FX
3U
-CF-ADP
35
SFC•STL
Programming
36
Interrupt
Function
37
Special Device
38
Error Code
A
Version Up
Information
B
Execution Times
Caution
1. Allowable number of writes to the memory
Note the following cautions on access to extension file registers.
•In FX
3U/FX3UC PLCs
Data can be written to the memory cassette (flash memory) up to 10,000 times.
Every time the INITR (FNC292), RWER (FNC294) or INITER (FNC295) instruction is executed, it is counted as a
write to the memory. Make sure not to exceed the allowable writes.
When a continuous operation type instruction is used, data is written to the memory in every operation cycle of the
PLC. For preventing this, make sure to use a pulse operation type instruction.
Execution of the LOADR (FNC290), SAVER (FNC291) or LOGR (FNC293) instruction is not counted as a write to
the memory. However, it is necessary to initialize the writing target sector before executing the SAVER (FNC291)
or LOGR (FNC293) instruction.
Every time the INITR (FNC292)or INITER (FNC295) instruction is executed, it is counted as a number of times of
writing to the memory. Make sure not to exceed the allowable number of writes.
•In FX
3G PLCs
Data can be written to the memory cassette (EEPROM) up to 10,000 times, and to the built-in memory (EEPROM)
up to 20,000 times.
Every time the RWER (FNC294) instruction is executed, it is counted as a write to the memory. Make sure not to
exceed the allowable number of writes.
When a continuous operation type instruction is used, data is written to the memory in every operation cycle of the
PLC. For preventing this, make sure to use a pulse operation type instruction.
Execution of the LOADR (FNC290)instruction is not counted as a write to the memory.
Errors
An operation error is caused in the following cases; The error flag M8067 turns ON, and the error code is stored in
D8067.
When the last device number to be transferred exceeds “32767” (error code: K6706)
At this time, devices up to the last one (R32767) are read and transferred.
When a memory cassette is not connected (error code: K6771)
*1
*1. An operation error is not caused in FX3G PLCs because the contents of extension file registers stored in the
EEPROM built in the PLC are read if a memory cassette is not connected.
Program example
In the program example shown below, the contents (current value) of 4000 extension file registers ER1 to ER4000
inside the memory cassette are read, and transferred to 4000 extension registers R1 to R4000 inside the built-in RAM.
M0
FNC290
LOADR
R1 K4000
ER1 K100
ER2 K50
ER3 H0003
ER4 H0101
ER3999 K55
ER4000 K59
Device
number
Current
value
R1 K100
R2 K50
R3 H0003
R4 H0101
R3999 K55
R4000 K59
Device
number
Current
value
Read
(transfer)
Extension file registers (ER)
inside memory cassette
Extension registers (R)
inside built-in RAM