Filter
Top Products
27
FX3G/FX3U/FX3UC Series Programmable Controllers
Programming Manual - Basic & Applied Instruction Edition
2 Overview (Sequence Program)
2.3 Analog/Positioning Special Control
1
Introduction
2
Overview
3
Instruction
List
4
Devices
in Detail
5
Specified the
Device &
Constant
6
Before
Programming
7
Basic
Instruction
8
FNC00-FNC09
Program Flow
9
FNC10-FNC19
Move & Compare
10
FNC20-FNC29
Arith. & Logic
Operation
4. Rotation and shift operation
• Rotation right (ROR/FNC 30)
• Rotation left (ROL/FNC 31)
• Rotation right with carry (RCR/FNC 32)
• Rotation left with carry (RCL/FNC 33)
• Bit shift right (SFTR/FNC 34)
• Bit shift left (SFTL/FNC 35)
• Word shift right (WSFR/FNC 36)
• Word shift left (WSFL/FNC 37)
→ Refer to Chapter 11.
5. Data operation
• Zone reset (ZRST/FNC 40)
• Decode (DECO/FNC 41)
• Encode (ENCO/FNC 42)
• Sum of active bits (SUM/FNC 43)
• Mean (MEAN/FNC 45)
• Word to byte (WTOB/FNC141) and byte to word
(BTOW/FNC142)
• 4-bit linking/grouping of word data
(FNC143 and FNC144)
• Limit control (LIMIT/FNC256)
• Dead band control (BAND/FNC257)
• Zone control (ZONE/FNC258)
• Block data operation (FNC192 to FNC199)
• Character string control (FNC200 to FNC209)
→ Refer to Chapter 12, Chapter 19,
Chapter 25, Chapter 26 and Chapter 29.
6. High speed processing
• Refresh (REF/FNC 50)
• Refresh and filter adjust (REFF/FNC 51)
• Speed detection (SPD/FNC 56)
• Pulse Y output (PLSY/FNC 57)
• Pulse ramp (PLSR/FNC 59)
→ Refer to Chapter 13.
7. Handy instructions and instructions for
external devices
• Initial state (IST/FNC 60)
• Teaching timer (TTMR/FNC 64)
• Alternate state (ALT/FNC 66)
• Ramp variable value (RAMP/FNC 67)
• Rotary table control (ROTC/FNC 68)
• Ten-key input (TKY/FNC 70)
• Digital switch (thumbwheel input) (DSW/FNC 72)
• Seven-segment decoder (SEGD/FNC 73)
• Seven-segment with latch (SEGL/FNC 74)
• ASCII code data input (ASC/FNC 76)
• BFM Read, BFM Write (FNC 78, FNC 79,
FNC278, and FNC279)
• Serial communication (FNC 80 and FNC 87)
• Analog volume (FNC 85 and FNC 86)
• Inverter communication (FNC270 to FNC274)
• Hexadecimal to ASCII conversion (ASCI/FNC 82)
• ASCII to hexadecimal conversion (HEX/FNC 83)
• Cyclic redundancy check (CRC/FNC188)
• Random number generation (RND/FNC184)
• Real time clock control (FNC160 to FNC167)
• Hour meter (HOUR/FNC 169)
• Timing pulse generation (DUTY/FNC186)
• Logging R and ER (LOGR/FNC293)
→ Refer to Chapter 14, Chapter 15,
Chapter 16, Chapter 21, Chapter 24, Chapter 30,
Chapter 31 and Chapter 33.
8. Complicated control
• Search a data stack (SER/FNC 61)
• Sort tabulated data (FNC 69 and FNC149)
• PID control loop (PID/FNC 88)
→ Refer to Chapter 14, Chapter 16 and
Chapter 19.
9. Positioning control
• Dog search zero return (DSZR/FNC150)
• Interrupt positioning (DVIT/FNC151)
• Batch data positioning mode (TBL/FNC152)
• Absolute present value read (ABS/FNC155)
• Zero return (ZRN/FNC156)
• Variable speed pulse output (PLSV/FNC157)
• Drive to increment (DRVI/FNC158)
• Drive to absolute (DRVA/FNC159)
→ Refer to Chapter 20.
→ Refer to the Positioning Control Manual.
2.3 Analog/Positioning Special Control
For details, refer to the manual of each product.
1. Analog I/O control
• Analog input
• Analog output
• Pt100 temperature sensor input
• Thermocouple temperature sensor input
• Block dedicated to temperature control
→ Refer to the respective product manual.
2. Positioning control
• SSCNETΙΙΙ - Positioning Block.
• Pulse output block (controlled by sequence
program)
• Positioning unit (controlled by instructions
dedicated to positioning)
• Cam switch (resolver detection)
→ Refer to the respective product manual.