Filter
Top Products
D9412GV2/D7412GV2 | Program Entry Guide | 2.0 GV2MAIN EN | 59
Bosch Security Systems, Inc. | 10/08 | F01U003636-04
•
•
For example: The Change Display (COMMAND
49) function has three sub-functions: Bright
Display, Dim Display, and Date/Time Display.
Programming Custom Function Keystrokes
•
Find the command you want to execute in the
User Interface section of the program record
sheet. Single digit commands must be
programmed with 9 as the second digit.
- To turn up the display, enter:
[A][4][9][E]
- To dim the display, enter:
[A][4][9][D][E]
Table 26: CF### Custom Function Keystrokes
- To display time and date, enter:
[A][4][9][B][E]
Command Keystroke
1 (Master arm area) A19
Custom Functions can perform several tasks at
one time. For example:
2 (Perimeter instant arm) A29
3 (Perimeter delay arm) A39
− To toggle relays 7, 8, and 9 in one Custom
Function enter:
[A] [5] [4] [7] [E] [E] [8] [E] [E] [9] [E] [E] [C]
6 (Watch Mode) A69
7 (Special alert) A79
8 (Perimeter partial arm) A89
9 ( Special alert) A99
− To add a temporary pass code, enter:
[A] [5] [6] [3] [0] [E] [E] [9] [8] [7] [E] [E] [D] [E]
[1] [E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E] [1] [E]
[1] [E] [C]
This adds user 30, pass code 987 with
authority level 1 in all areas.
0 (Bypass a point) A09
•
•
When CF### Custom Function is programmed
with P, the corresponding custom function
number is passcode protected. The CF###
Custom Function prompt is under GV2MAIN >
User Interface > Cmd Center Functions. The
passcode protected custom function can be
added to a keypad’s function list by programming
its number in the GV2MAIN > Function List > M#
Function prompt.
− To delete the pass code, enter:
[A] [5] [3] [3] [0] [E] [E] [E] [C]
To program multiple-area Arming or Disarming
functions, use keystroke sequences including
COMMAND 50 (Move to Area) and
COMMAND 1.
128 to 143 Enable Custom Function 128
through 143, (Menu Function only): This
function determines if a pass code is needed to
access a Custom Function from the menu list.
ENTER PASSCODE (or Enter Passcode + Enter
Key on the D1260) appears when this function is
pass-code protected.
Custom function cannot be used to
change time (such as Daylight Saving
Time). Use Skeds S## Function Codes
13 and 14 to adjust for Daylight Saving
Time (refer to S## Custom Function
prompt in Section 5.2 Skeds on page
115.
If a command within the Custom Function
Example 1
is pass-code protected, ENTER
Execute the third function in a keypad menu function
list:
PASSCODE appears at the keypad. The
user must enter a valid pass code before
proceeding with the rest of the Custom
Function. If a pass code is not entered
within 10 sec, the Custom Function times
out and the display returns to idle text.
D1255 CDDE
D1260 C8C7C5
The custom functions in Example 1 are
not compatible between keypad types.
Skeds cannot execute Custom Functions
that are pass-code protected. The D720
LED keypad does not support Custom
Example 2
Functions that are pass-code protected.
Instant master Arm (CMD 11):
Some functions cannot be entered directly
because they are nested inside a higher-level
function. To automatically execute these
functions, you must add the appropriate
keystrokes.
D1255 A11
D1260 A11
The custom functions in Example 2 are
compatible between keypad types.