Filter
Top Products
D9412GV2/D7412GV2 | Program Entry Guide | 2.0 GV2MAIN EN | 19
Bosch Security Systems, Inc. | 10/08 | F01U003636-04
Test Reports
Restoral Reports are not sent if the
control panel resets after a point is
bypassed and then unbypassed. This is
true for both Fire and Non-fire points.
To meet UL 864 requirements for
Central Station and Remote Station
applications, enable Test Reports.
User Reports
Sending Test Reports
Automatic: To send a single Test Report (R# Test
Report) automatically, enable Sked Function Code
#9 (Test Report) in the Skeds section of the program.
Refer to
Selecting Yes enables a report to be sent when the
event occurs.
Table 12: User Reports
Table 13.
Manual: To send a single Test Report manually,
enter [COMMAND][4][3] at the keypad. Refer to the
Report Report Description
Selection
s
prompt on page 63. Send Report
To expand this Test Report to include any off-normal
point condition or other off-normal system conditions,
Expand Test Rpt (refer to page
Yes, No Point Bypass Event
R# Point
Bypass
12) must be
programmed Yes. Refer to the footnotes with
Yes, No Forced Point Event
R# Forced
Point
Table
14
on page 20 for a list of event types that are
included in an expanded test report. Additionally, the
expanded test report includes Summary Fire
Supervisory, Summary Fire Fault, Summary
Controlled Point Fault, and Summary Point Device
Fault conditions.
Yes, No Point Opening Event
R# Point
Open
Yes, No Point Closing Event
R# Point
Close
Yes, No Point Force Armed
R# Forced
Arm
The control panel can generate an Expanded Off-
Normal Test Report by using Sked Function Code 28
or a Non-Expanded Off-Normal Test Report using
Sked Function Code 29. To generate this event, one
or more points must be in an off-normal state at the
time the Sked executes. Expanded Off-Normal Test
Reports include the Off Normal Test Report Event as
well as a panel-wide summary of off-normal point and
system conditions. Non-Expanded Off-Normal Test
Report Events are sent only when a point is in the off-
normal state but sends only the Off-Normal Test
Report Event.
Yes, No Fail to Open Event
R# Fail To
Open
Yes, No Fail to Close Event
R# Fail To
Close
Yes, No
R# Ext Clos
Tm
Extend Close Time
Event
Yes, No Opening Events
R# Opening
Rpt
Yes, No
R# Forced
Close
Point Forced Close
Event
Yes, No Closing Events
R# Closing
Rpt
Sending Status Reports
Automatic: To send a Status Report automatically
that includes the events shown in the footnotes in
Yes, No
R# FC Perim
Inst
Forced Close
Perimeter Instant
Armed Event
Table 13, enable Sked Function Code #10 in the
Skeds section of the program.
Yes, No
R# FC Perim Forced Close
Delay Perimeter Delay
Armed Event
Manual: To send a Status Report manually that
includes the events shown in the footnotes in
Table
13
, enter [COMMAND][4][2] at the keypad. Refer to
the
Yes, No
R# Perim Inst
Arm
Perimeter Instant
Armed Event
prompt on page 63. Send Report
Sending off-normal conditions as a Status Report
following a Test Report is required by some
automation systems. Sending off-normal conditions
as a Non-status Report that follows a Test Report is
required for other automation systems.
Yes, No
R# Perim Perimeter Delay
Delay Arm Armed Event
Yes, No User text
R# Send User
Text
An off-normal condition is any point that is missing,
trouble, supervisory, or in alarm. Also, points not
cleared at the keypad report as off-normal.