Filter
Top Products
25
Report Code, Alarm (Zones 1 - 32)
Cmd Loc 001 002 003 004 005 006 007 008 009 010 011 012
Default 01 01 0 1 01 01 01
Zone 1 2 3 4 5 6
Cmd Loc 013 014 015 016 017 018 019 020 021 022 023 024
Default 0 1 0 1 0 1 0 1 0 1 0 1
Zone 7 8 9 10 11 12
Cmd Loc 025 026 027 028 029 030 031 032 033 034 035 036
Default 0 1 0 1 0 1 0 1 0 1 0 1
Zone 13 14 15 16 17 18
Cmd Loc 037 038 039 040 041 042 043 044 045 046 047 048
Default 0 1 0 0 0 1 0 1 0 1 0 1
Zone 19 20 21 22 23 24
Cmd Loc 049 050 051 052 053 054 055 056 057 058 059 060
Default 0 1 0 1 0 1 0 1 0 1 0 1
Zone 25 26 27 28 29 30
Cmd Loc 061 062 063 064
Default 0 1 0 1
Zone 31 32
Range 0 - 15 (All CL)
Block 5 - Reporting Digits Programming
This Block has 180 Command Locations (CL 001 - 180). Certain reporting formats such as CFSK-IV, Contact ID, and SIA
have pre-defined codes and the data programmed here is ignored. Reports may be disabled by programming the
reporting code as 0 (or 00 for two-digit codes). Each Cmd Loc may be programmed with any value from 0 - 15.
Comments
These codes are used to indicate alarm conditions. Each report code is a
two-digit code. Reports may be disabled by programming a value of 00
into the Cmd Loc. Each location may contain any digit from 0 - 15.
NOTE: The programmed digits 10 - 15 will be sent to the central station as
their hexadecimal equivalent, as shown in the table below:
Comments
Amount of time (in minutes) that the phone line must be cut (open) before
annunciation will occur and a report is sent to the central station. This is also
the time interval required before the phone line cut action (Block 3, CL 036
and 037). Programming either command location with 0 will disable phone
line checking for that line.
If the system is equipped with a single-line digital communicator, the pro-
gramming of CL 163 will be ignored.
Test Report Phone Line Routing
Cmd Loc 164
Default 1
Range 1 - 3
Comments
This option allows the installer to select the phone line
which will be used to send test reports. If a dual-line
digital communicator is used, both lines may be se-
lected for test reporting. The data programmed in
this location overrides the programming of Block 4,
CL 112 for test reports only.
Telephone Line #1 Supervision Time (Minutes)
Cmd Loc 162
Default 5
Range 0 - 30
Telephone Line #2 Supervision Time (Minutes)
Cmd Loc 163
Default 5
Range 0 - 30
Options:
1 Line #1 Only
2 Line #2 Only
3 Line #1 and
Line #2
Block 4 - Digital Communicator Programming (cont.)
Audio Verification Enable (Listen-In)
Cmd Loc 160
Default 1
Range 1 - 4
Options:
1 No Audio Verification (AV)
2 Trigger AV following alarm, but before releasing line. Panel may not
seize line for 3 min. or send reports until AV session is complete.
3 Same as option #1, but allows reports to interrupt AV session.
4 Same as option #1, except retriggers AV when panel attempts to
seize line to send alarm report.
Keypad and Accessory Communications
Trouble Report Routing
Cmd Loc 159
Default 2
Range 1 - 5
Comments
Report routing for all communication trouble
and restoral reports associated with keypads
and accessories connected to the system.
Digital Communications Enable
Cmd Loc 161
Default 1
Range 1 - 2
Comments
If disabled, programmed for No (1), the sys-
tem will operate as a local system. Phone line
checking will also be disabled. For reporting
systems, program this location as Yes (2).
Options:
1 No (Local System)
2Yes
Options:
1 Disable Reports
2 Receiver 1 Only
3 Receiver 2 Only
4 Receivers 1 and 2
5 Receiver 1, with
Receiver 2 as Back-
up, Alternating
Reporting Digit Conversion:
Decimal Hexadecimal
10 A
11 B
12 C
13 D
14 E
15 F