Filter
Top Products
E-20
Using Built-in Tones (Tutorial)
02: Compressor
Compresses the input signal, which can have the effect of
suppressing level variation and can make it possible to sustain
dampened sounds longer.
Parameter Value Ranges:
1 :Attack (0 to 127)
Adjusts the attack amount of the input signal. A smaller value
causes prompt compressor operation, which suppresses the attack
of the input signal. A larger values delays compressor operation,
which causes the attack of the input signal to be output as-is.
2 :Release (0 to 127)
Adjusts the time from the point the input signal drops below a
certain level until the compression operation is stopped.
When an attack feeling is desired (no compression at the onset of
sound), set this parameter to as low a value as possible. To have
compression applied at all times, set a high value.
3 :Depth (0 to 0 to 127)
Adjusts compression of the audio signal.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
Output volume changes in accordance with the Depth setting and
the characteristics of the input tone.
5 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
03: Limiter
Limits the input signal level so it does not rise above a preset level.
Parameter Value Ranges:
1 :Limit (0 to 127)
Adjusts the volume level of the limit at which limiting is applied.
2 :Attack (0 to 127)
Adjusts the attack amount of the input signal.
3 :Release (0 to 127)
Adjusts the time from the point the input signal drops below a
certain level until the limit operation is stopped.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound. Output volume changes in
accordance with the Limit setting and the characteristics of the
input tone. Use this parameter to correct for such changes.
5 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
04: Enhancer
Enhances the profiles of the low range and high range of the input
signal.
Parameter Value Ranges:
1 :Low Frequency (0 to 127)
Adjusts the low range enhancer frequency.
2 :Low Gain (0 to 127)
Adjusts the low range enhancer gain.
3 :High Frequency (0 to 127)
Adjusts the high range enhancer frequency.
4 :High Gain (0 to 127)
Adjusts the high range enhancer gain.
5 :Input Level (0 to 127)
Adjusts the input level.
6 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
7 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
05: Early Reflection
An effector that extracts early reflections from reverb.
Applies acoustic presence to notes.
Parameter Value Ranges:
1 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
2 :Feedback (0 to 127)
Adjusts the repeat of the reflected sound.
3 :Tone (0 to 127)
Adjusts the tone of the reflected sound.
4 :Input Level (0 to 127)
Adjusts the input level.
5 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
06: Phaser
Produces a distinctive pulsating, broad sound by using an LFO to
change the phase of the input signal and then mixes it with the
original input signal.
Parameter Value Ranges:
1 :Resonance (0 to 127)
Adjusts the strength of feedback
2 :Manual (–64 to 0 to +63)
Adjusts the reference phaser shift amount.
3 :LFO Rate (0 to 127)
Adjusts the LFO rate.
4 :Depth (0 to 127)
Adjusts the LFO depth.
5 :LFO Waveform (Sin, Tri, Random)
Selects the LFO waveform.
6 :Input Level (0 to 127)
Adjusts the input level.
7 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
8 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
07: Chorus
Gives notes depth and breadth.
Parameter Value Ranges:
1 :LFO Rate (0 to 127)
Adjusts the LFO rate.
2 :Depth (0 to 127)
Adjusts the LFO depth.
3 :LFO Waveform (Sin, Tri)
Selects the LFO waveform.
4 :Feedback (–64 to 0 to +63)
Adjusts the strength of feedback
5 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
6 :Polarity (–, +)
Inverts the LFO of one channel.
7 :Input Level (0 to 127)
Adjusts the input level.
8 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
08: Flanger
Applies wildly pulsating and metallic reverberation to notes. Selects
the LFO waveform.
Parameter Value Ranges:
1 :LFO Rate (0 to 127)
Adjusts the LFO rate.
2 :Depth (0 to 127)
Adjusts the LFO depth.
3 :LFO Waveform (Sin, Tri, Random)
Selects the LFO waveform.
4 :Feedback (–64 to 0 to +63)
Adjusts the strength of feedback
5 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
6 :Input Level (0 to 127)
Adjusts the input level.
7 :Dry Level (0 to 127)
Adjusts the level of the direct sound.
09: Tremolo
Shifts the volume of the input signal using an LFO.
Parameter Value Ranges:
1 :LFO Rate (0 to 127)
Adjusts the LFO rate.
2 :Depth (0 to 127)
Adjusts the LFO depth.
3 :LFO Waveform (Sin, Tri, Tra)
Selects the LFO waveform.
4 :Wet Level (0 to 127)
Adjusts the level of the effect sound.
5 :Dry Level (0 to 127)
Adjusts the level of the direct sound.