Filter
Top Products
Using Built-in Tones (Tutorial)
E-15
Editable Parameters
Display Text Description Settings
Layer On/Off Layer on/off. Selecting off disables layer. Off, On
Wave Number
Wave number. Selects a waveform type.
• Refer to the “Wave List” at the back of this manual for information
about wave types.
See “Wave List” at the
back of this manual.
Pitch >Ent
Pitch envelope. For details, see the melody tone “Pitch Envelope” on
page E-11.
• For details about the setting items below, see the melody tone “Pitch
Envelope” on page E-11. You can input “Initial Level” and “Release
Level” values in the range of –256 to 0 to +255. You can input “Attack
Time” and “Release Time” values in the range of 0 to 127.
Octave Shift, Initial Level, Attack Time, Release Time, Release Level
• For details about the setting items below, see drum tone “Pitch
Envelope” on page E-13.
Coarse Tune, Fine Tune
• For details about the setting items below, see the melody tone
“Filter” on page E-11. You can input “Attack Level” and “Decay
Level” values in the range of –256 to 0 to +255. You can input a
“Decay Time” in the range of 0 to 127.
Attack Level, Decay Time, Decay Level
Key Follow
Key follow. Adjusts the amount of pitch change between neighboring
keyboard keys. A higher value represents greater change.
–128 - 0 - +127
Key Follow Base Key follow base. Keyboard key that is the center of key follow. C- - G9
Split Shift
Split shift. Counting from the keyboard key that is pressed, the
waveform that sounds is the one assigned to the keyboard key that is
the specified split shift amount above or below the pressed key. The
pitch used is the one that corresponds to the pressed keyboard key.
–12 - 0 - +12
LFO Layer Depth LFO layer depth. Adjusts how LFO is applied to each layer. 0 - 127
Filter >Ent
Filter. For details, see the melody tone “Filter” on page E-11.
• For details about the setting items below, see the melody tone
“Filter” on page E-11. You can input a value in the range from 0 to
127.
Cutoff, Resonance, Attack Level, Envelope Depth
• For details about the setting items below, see the melody tone “Pitch
Envelope” on page E-11. You can input a value in the range from 0 to
127.
Initial Level, Attack Time
Filter Type
Filter type. Specifies the range cut by the filter.
LPF1: 6dB/oct filter for low-frequency band components. No
resonance effect. Suitable for acoustic instruments.
LPF2: 12dB/oct filter for low-frequency band components. No
resonance effect. Suitable for acoustic instruments.
LPF3: 12dB/oct filter for low-frequency band components. With
resonance effect. Suitable for synthesized tones.
BPF : 6dB/oct filter for band components in the vicinity of the cutoff
frequency. With resonance effect.
HPF : 12dB/oct filter for high-frequency band components. With
resonance effect.
Refer to the cell to the left.
Velocity Sense
Velocity sense. Specifies the degree of change in the filter in accordance
with keyboard press velocity.
–64 - 0 - +63
Decay 1 Time
Decay 1 time. Time it takes for the sound to reach the decay 1 level
from the attack level.
0 - 127
Decay 1 Level
Decay 1 level. Target level for change from the attack level up to the
Decay 1 level.
0 - 127
Decay 2 Time
Decay 2 time. Time it takes for the sound to reach the Decay 2 level
from the Decay 1 level.
0 - 127
Decay 2 Level
Decay 2 level. Second target level for change from Decay 1 level up to
the Decay 2 level.
0 - 127