DVP-ES2/EX2/SS2/SA2/SX2/SE Operation Manual - Programming
2-18
Special
M
Function
ES2
EX2
SS2 SA2 SX2
OFF
Ø
ON
STOP
Ø
RUN
RUN
Ø
STOP
Attrib.
Latch
-ed
Default
M1020 Zero flag
○ ○ ○ ○
OFF - - R NO OFF
M1021 Borrow flag
○ ○ ○ ○
OFF - - R NO OFF
M1022 Carry flag
○ ○ ○ ○
OFF - - R NO OFF
M1024 COM1 monitor request
○ ○ ○ ○
OFF - - R/W NO OFF
M1025*
Indicate incorrect request for
communication
○ ○ ○ ○
OFF - - R NO OFF
M1026 RAMP mode selection
○ ○ ○ ○
OFF - - R/W NO OFF
M1027 PR output mode selection (8/16 bytes)
○ ○ ○ ○
OFF - - R/W NO OFF
M1028
Switch T64~T126 timer resulotion
(10ms/100ms). ON =10ms
○ ○ ○ ○
OFF - - R/W NO OFF
M1029*
CH0 (Y0, Y1) pulse output execution
completed.
○ ○ ○ ○
OFF - - R NO OFF
M1030*
Pulse output Y1 execution completed
○ ○ ○ ○
OFF - - R NO OFF
M1031* Clear all non-latched memory
○ ○ ○ ○
OFF - - R/W NO OFF
M1032* Clear all latched memory
○ ○ ○ ○
OFF - - R/W NO OFF
M1033* Output state latched at STOP
○ ○ ○ ○
OFF - - R/W NO OFF
M1034* Disable all Y outputs
○ ○ ○ ○
OFF - - R/W NO OFF
M1035*
Enable X7 input point as RUN/STOP
switch
○ ○ ○ ○
- - - R/W YES OFF
M1037*
Enable 8-sets SPD function (Has to be
used with D1037)
╳ ╳ ○○
OFF OFF OFF R/W NO OFF
M1038
Switch T200~T255 timer resulotion
(10ms/1ms). ON = 1ms
○ ○ ○ ○
OFF - - R/W NO OFF
M1039* Fix scan time
○ ○ ○ ○
OFF - - R/W NO OFF
M1040 Disable step transition
○ ○ ○ ○
OFF - - R/W NO OFF
M1041 Step transition start
○ ○ ○ ○
OFF - OFF R/W NO OFF
M1042 Enable pulse operation
○ ○ ○ ○
OFF - - R/W NO OFF
M1043 Zero return completed
○ ○ ○ ○
OFF - OFF R/W NO OFF
M1044 Zero point condition
○ ○ ○ ○
OFF - OFF R/W NO OFF
M1045 Disable “all output reset” function
○ ○ ○ ○
OFF - - R/W NO OFF
M1046 Indicate STL status
○ ○ ○ ○
OFF - - R NO OFF
M1047 Enable STL monitoring
○ ○ ○ ○
OFF - - R/W NO OFF
M1048 Indicate alarm status
○ ○ ○ ○
OFF - - R NO OFF
M1049 Enable alarm monitoring
○ ○ ○ ○
OFF - - R/W NO OFF
M1050 Disable interruption I000 / I001
○ ○ ○ ○
OFF - - R/W NO OFF
M1051 Disable interruption I100 / I101
○ ○ ○ ○
OFF - - R/W NO OFF
