WARNING
Electrical shock hazard!
This appliance is equipped with a three-prong (grounding)
polarized plug for your protection against possible shock
hazards. Electrical Grounding Required.
u
Do not remove the round grounding prong from the
plug.
u
Use only an grounded adapter.
-
Wait 1 hour after installation before you plug in the
appliance. This allows the refrigerant and system lubri-
cation to reach equilibrium.
-
Make sure incoming voltage is the same as the appli-
ance rating. A 110-120 Volt, 60 Hz, 15 Amp electrical
supply (20 Amp for side-by-side installations) circuit
that is controlled by a circuit breaker or fuse is required.
-
We recommend using a dedicated circuit for this appli-
ance to prevent electrical overload.
-
Follow all Federal, State and local electrical, fire and
building codes and ordinances when installing the
receptacle and / or the appliance.
-
In some communities, a wall switch is required to turn
power to the appliance ON and OFF.
-
To reduce the risk of fire, electric shock, or personal
injury, installation work and electrical wiring must be
done by a qualified electrician in accordance with all
applicable codes and standards, including fire-rated
construction.
-
The Power Plug must be easily accessible so that the
appliance can be disconnected from the mains quickly
in an emergency. It must not be behind the back of the
appliance.
-
The top of the electric outlet must be located within
82-5/8 in. (2100 mm) from the top of the base in the
cabinet.
4.5 Switching on the appliance
w
Whenever “DEMO” appears on the display, the appli-
ance is running in demonstration mode. Contact the
customer service department.
4.6 Switching on the appliance
Note
u
To switch on the entire appliance, only the freezer
compartment needs to be switched on.
Switch on the appliance 2 hours before loading
with frozen food for the first time.
Do not load frozen foods until the temperature
display reads 0 °F (-18 °C).
4.6.1 Switching on the freezer compartment
u
Open the door.
u
Press On/Off button, freezer compartment
Fig. 2 (3)
.
w
The temperature display for the wine cooling zone and
the Alarm symbol will flash until the set temperature is
reached.
w
The freezer compartment temperature display and the
Alarm symbol will flash until the temperature is cold
enough. If the temperature is greater than 32 °F (0 °C),
flashing dashes will appear; if the temperature is lower
than this, the current temperature will flash on the
display.
w
Whenever “DEMO” appears on the display, the appli-
ance is running in demonstration mode. Contact the
customer service department.
4.6.2 Switching on the wine cooling zone
u
Open the door.
u
Press Wine cooling zone On/Off button
Fig. 2 (15)
.
w
The temperature display for the wine storage zone and
the Alarm symbol will flash until the set temperature is
reached.
5 Operation
5.1 Temperature display unit
The temperature display can be changed from °F to °C.
5.1.1 To change the unit
u
Activate setting mode: Press SuperFrost button
Fig. 2 (2)
for about 5 seconds.
w
S is displayed in the temperature display.
w
The Menu symbol
Fig. 2 (22)
lights up.
u
Using Freezer compartment Up button
Fig. 2 (5)
/ Freezer compartment Down button
Fig. 2 (4)
select °.
u
To confirm: Briefly press SuperFrost button
Fig. 2 (2)
.
u
Using Freezer compartment Up button
Fig. 2 (5)
/ Freezer compartment Down button
Fig. 2 (4)
select °F or °C.
u
To confirm: Briefly press SuperFrost button
Fig. 2 (2)
.
u
To exit setting mode: Press Freezer compartment
On/Off button
Fig. 2 (3)
.
-or-
u
Wait 5 minutes.
w
The temperature is again displayed in the temperature
display.
5.2 Brightness of the temperature
display
You can adapt the brightness of the temperature display
to the light conditions in the room in which it is installed.
If the door is open or the control panel is used the temper-
ature indicator lights up at maximum brightness. About 1
minute after the door is closed or no button has been
Operation
* Depending on model and options 7
