Filter
Top Products
35
Reference
VQT5F61
The TV screen turns black.
¾ When “24p Output” is set to “On”, HDMI
authentication takes place and a black screen
is displayed.
This unit does not recognize the USB
connection correctly.
¾ Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
¾ USB devices may not be recognized by this
unit when connected using the following :
ja USB hub
ja USB extension cable other than the
supplied with the Wireless LAN Adaptor
DY-WL5 (optional)
¾ If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
The unit switches to standby mode.
¾ This unit will automatically turn to standby
mode after 20 minutes if it is inactive. (> 15)
¾
When the time set for the sleep timer has
passed, the main unit will be turned off. (
>
9)
¾
One of the unit’s safety devices is activated.
Press [
Í
/I] on the main unit to turn the unit on.
The images from this unit do not appear on
the TV.
Picture is distorted.
Jittering occurs.
¾ An incorrect resolution is selected in “HDMI
Video Format”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
j“00rEt” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “04PrG” is displayed on the unit’s
display.
4 Press and hold [OK] for at least 5 seconds.
Set the item again. (> 26)
jWhen Dolby Digital Plus, Dolby TrueHD,
and DTS-HD
®
audio are not output properly,
select “Yes” in “Default Settings” (> 31) and
make proper settings.
¾ The unit and TV are using different video
systems.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
j“00rEt” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “05Pln” is displayed on the unit’s
display.
4 Press and hold [OK] for at least 5 seconds.
The system switches from PAL to NTSC or
vice versa.
¾ PAL discs cannot be correctly viewed on an
NTSC TV.
¾ When “3D BD-Video Playback” in the Setup
menu is set to “Automatic”, images may not
be output depending on the connection
method. After removing the disc from this unit,
select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 27)
¾ If irregular colouring occurs on your TV, turn
the TV off for about 30 minutes.
If it persists, move the speakers further away
from the TV.
Video is not output in high-definition.
¾ Confirm that “HDMI Video Format” in the
Setup menu is set properly. (> 26)
3D video is not output.
¾ Connect to a full high-definition TV.
¾ Are the settings on this unit and the TV
correct? (> 18)
¾ Depending on the connected TV, the video
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
¾ Check that proper HDMI video input is
selected on the TV.
3D video is not output correctly as 2D.
¾ Select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 27, “3D
BD-Video Playback”)
¾ Discs that have recorded titles with Side by
side (2 screen structure) and that can be
enjoyed in 3D are played back in accordance
with the settings of the TV.
A black band is displayed around the edge of
the screen.
The aspect ratio of the screen is abnormal.
¾
Confirm the “TV Aspect” is set properly. (
>
29)
¾ Adjust the aspect setting on the TV.
Picture
SC-BTT785&465&433&405GNGSGA-VQT5F61_mst.book 35 ページ ２０１４年２月２７日 木曜日 午前１１時２７分