Filter
Top Products
3
For maximum comfort, keep your elbows
close to your sides and rest your forearms
on your lap if you play for a long time.
Notes:
• You cannot use the thumb-control pad
when the gamepad is set to analog
mode. You cannot use the joystick when
the gamepad is set to digital mode.
• In either mode, you can use either
thumb to set the
A
,
B
,
R1/R2
,
C
,
D
,
T1/
T2
,
ANALOG/DIGITAL
, or
THROTTLE/T1/
T2
switches.
Using the Joystick
The joystick works when the gamepad is set to
analog mode (see Step 5 under “Using the
Gamepad” on Page 2).
Using the Analog Throttle
The analog throttle (marked
THROTTLE
) works
when the gamepad is set to analog or digital
mode (see “Using the Gamepad” on Page 2).
To use the analog throttle, set
THROTTLE/T1/
T2
to
THROTTLE
. This disables the
T1
and
T2
buttons. Then slide the
THROTTLE
switch to
the desired level. To disable the analog throt-
tle, set
THROTTLE/T1/T2
to
T1/T2
. This acti-
vates the
T1
and
T2
buttons.
Note:
The analog throttle works only with
games that support analog mode.
CONFIGURING THE
GAMEPAD IN WINDOWS 95/98
(WITHOUT THE SUPPLIED
DRIVER)
1. Set the
R1/R2
and
T1/T2
switches to
NOR-
MAL
.
2. If you want to use the gamepad’s throttle,
set the
THROTTLE/T1/T2
switch to
THROT-
TLE
.
3. From the Start Menu, select
Settings
,
then click on
Control Panel
.
4. Double-click the
Game Controllers
icon.
5. Remove any previously selected control-
ler drivers.
6. Click on
Add
.
7. Select
Custom
under
Joystick Selec-
tion
.
8. Enter a name for the controller, select
4
Axes
and
4 Buttons
, then click
OK
.
9. Select the mode you want to use (
Analog
or
Digital
), then click on
Properties
.
10. Highlight the name of the controller you
entered in Step 8, then click on
Proper-
ties
.
11. Click on
Calibrate
then press the control-
ler’s buttons to calibrate it.
12. If your game uses a throttle control, cali-
brate it by alternately pressing
T1
and
T2
several times (if you set
THROTTLE/T1/T2
to
T1/T2
), or slide
THROTTLE
back and
forth several times (if you set
THROTTLE/
T1/T2
to
THROTTLE
). If your game uses a
rudder control, calibrate it by alternately
pressing
R1
and
R2
several times.
13. When you have finished calibrating the
gamepad, click
FINISH
then click
TEST
.
Press the gamepad’s buttons to test it.
Note:
During the test, the throttle and rud-
der indicators should appear in the center
of the two vertical bars. These indicators
move up when you press
T1
or
R1
and
move down when you press
T2
or
R2
. Do
not press
T1
and
T2
or
R1
and
R2
at the
same time.
CALIBRATING THE GAMEPAD
USING THE SUPPLIED
DRIVER
Important:
• If you install a game card that works at a
different speed after you calibrate your
gamepad, you must re-calibrate the
gamepad.
• The supplied driver works only with 1-
player 8-button configuration.
Note:
Make sure the gamepad is set to the
mode you want (digital or analog) before you
calibrate it. See Step 5 under “Using the
Gamepad” on Page 2.
26-446.fm Page 3 Friday, July 9, 1999 9:45 AM