■■
Unpack dispenser components.
■■
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
■■ Unscrew and remove threaded extension
from valve body. Do not discard, as you
will need this later (See Figure 1).
■■ Leave small washers in place.
■■ Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
■■ From under sink, slide 2
1
⁄4" fiber washer
over faucet base. Reinstall threaded
extension onto the base until snug.
Thread star nut onto extension until
snug (See Figure 2).
■■ From under sink, slide 2
1
⁄4" fiber washer
over threaded extension. Thread star
nut onto extension until snug.
Hot & Cool models only
■■ Attach the quick connector to the ends
of the copper tubes running from the
dispenser.
■■ Install a white 3/8" tube into other end
of quick connector.
If sink/counter thickness exceeds 3/4"
a hole diameter of 1
1
⁄2" is required.
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
2
A
C
View/Wave
View/Wave
Hot & Cool models only
6
For a standard
1
1
⁄
2
"
sink/counter hole
■■ Feed tubes down through the hole in
the sink/counter until the base is at
rest. Set faucet at desired angle.
Large washer required for sink holes larger
than
1
1
⁄
2
"
or for porcelain sinks with radius
or beveled holes.
■■
Before feeding tubes through sink
hole, remove extension. Place 2
1
⁄4"
large steel washer over threads on
faucet base. Reinstall extension.
B
View/Wave
Faucet is factory-ready for installation
into a standard 1
1
⁄2" sink/counter hole.
1
5
⁄8" Small
Steel Washer
2
1
⁄4" Large
Steel Washer
1
5
⁄8" Rubber
Washer
7
Standard 1
1
⁄2" hole Hole larger than 1
1
⁄2"
Installing into hole smaller than 1
1
⁄2"
Figure 1 Figure 2
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
1
5
⁄8" Small
Steel Washer
1
5
⁄8" Small
Rubber Washer
1
5
⁄8" Small
Steel Washer
1
5
⁄8" Small
Rubber Washer
INSTALLING THE FAUCET - VIEW/ WAVE
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
Make sure to use rubber gasket
to ensure proper seal.
2
B
A
■■
Unpack dispenser components.
■■
On a firm, flat surface, carefully
straighten the copper tubing using
hands only.
■■ Ensure that the black rubber gasket
is properly seated into the base of
the dispenser head and will
surround the sink mount.
■■ Feed tubes down the hole in the
sink or countertop until the base is
at rest on the sink or countertop
surface.
■■ From under the sink, place the
semi-circular mounting plate onto the
threaded stud.
■■ Place wing nut onto the threaded
stud. Make sure faucet head is at the
desired angle. Tighten the wing nut
until snug, while ensuring the semi-
circular mounting plate extends
beyond the sink hole.
An assistant may be needed to hold
the dispenser head in place
while securing the dispenser.
C
H990
H990
H990
INSTALLING THE FAUCET - H990
