Plantronics CA12CD-S Video Game Headset User Manual


 
www.plantronics.com
2014 Plantronics, Inc. All rights reserved
Plantronics, the logo design, and Sound Innovations
are trademarks or registered trademarks of Plantronics, Inc.
Printed in U.S.A.
201528-01 (05.14)
AC Adapters
North America (shown):
64401-03
European Union and
United Kingdom:
38640-01 (not shown)
Australia: 66804-01
(not shown)
Battery Pack
80322-01
Remote
North America
201059-01
UPCS
(DECT 6.0)
Countries outside
of North America
201059-02 (DECT)
Please note that the older spare
Remotes (PNs 80323-01 and
80323-02) will not work with the
CA12CD-S
FCC PART 15 REQUIREMENTS
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined
by turning the radio or television off and on, the user is encouraged
to try to correct interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
Exposure to Radio Frequency Radiation
This device and its antenna must not be co-located or operated in
conjunction with any other antenna or transmitter. To comply with
FCC RF exposure requirements, use only the supplied antenna.
The radiated output power of this internal wireless radio is far below
the FCC radio frequency exposure limits. Nevertheless, the wireless
radio shall be used as described in the manual.
The internal wireless radio operates within guidelines found in radio
frequency safety standards and recommendations, which reflect the
consensus of the scientific community.
Plantronics therefore believes the internal wireless radio is safe for
use by consumers. The level of energy emitted is far less than the
electromagnetic energy emitted by wireless devices such as mobile
phones. However, the use of wireless radios may be restricted in
some situations or environments, such as aboard airplanes. If you are
unsure of restrictions, you are encouraged to ask for authorization
before turning on the wireless radio.
In order to comply with FCC and IC RF Exposure requirements,
the base must be installed and operated such that a minimum
separation distance of 20 cm is maintained between the base and
all persons during normal operation. The Remote complies with FCC
radiation limits set forth for an uncontrolled environment.
NOTE: Modifications not expressly approved by Plantronics, Inc.
could void the user’s authority to operate the equipment.
INDUSTRY CANADA REGULATORY INFORMATION
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This equipment complies with IC radiation exposure limits set forth
for an uncontrolled environment.
Cet équipement est conforme aux limites d’exposition de radiation
IC énoncés pour un environnement non contrôlé.
CAN ICES-3 (B)/NMB-3(B)
LIMITED WARRANTY
•Thiswarrantycoversdefectsinmaterialsandworkmanshipof
products manufactured, sold or certified by Plantronics that were
purchased and used in the United States.
•Thewarrantylastsforoneyearfromthedateofpurchaseofthe
products.
•Thiswarrantyextendstoyouonlyifyouaretheenduserwiththe
original purchase receipt.
•Wewill,atouroption,repairorreplacetheproductsthatdonot
conform to the specification. We may use functionally equivalent
reconditioned, refurbished, remanufactured, pre-owned or new
products or parts.
•ToobtainserviceintheU.S.,contactPlantronicsat800-544-4660.
•THISISTHECOMPLETEPLANTRONICSWARRANTYFORTHE
PRODUCTS.
•Thiswarrantygivesyouspeciclegalrights,andyoumayalsohave
other rights that vary from state to state. Please contact your dealer or
our service center for the full details of our limited warranty, including
items not covered by this limited warranty.
TECHNICAL ASSISTANCE
Visit our Web site at www.plantronics.com/support for technical support
including frequently asked questions, compatibility and accessibility
information. The Plantronics Technical Assistance Center (TAC) is also
readytoassistyouon800-544-4660.
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product. The
symbol identifies and alerts the user to the presence of important
operating and service instructions.
3. Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not locate Base Unit near water, for example, near a bathtub or
sink, in a wet basement, or near a swimming pool.
5. This product should never be placed near or over a radiator or heat
register. This product should not be placed in a built-in installation
unless proper ventilation is provided.
6. Thisproductshouldbeoperatedonlyfromthetypeofpowersource
indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your dealer or local power
company.
7. Do not locate this product in an area where the power cord is likely
to be damaged by furniture or foot traffic.
8. Do not overload outlets and extension cords as this can result in the
risk of fire or electric shock.
9. Never push objects of any kind into this product through Base Unit
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid of
any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product,
but take it to qualified service personnel when service or repair
work is required. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause
electric shock when the product is subsequently used.
11. Avoid using telephone equipment during an electrical storm. There
may be a remote risk of electric shock from lightning.
12. Do not use the telephone equipment to report a gas leak in the
vicinity of the leak.
13. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power supply cord or plug is damaged or frayed.
b) If the product has been exposed to liquid.
c) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are covered
by the operating instructions because improper adjustments of
other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to normal
operation.
d) If the product has been dropped or the Base Unit has been
damaged.
e) If the product exhibits a distinct change in performance.
14. Never install telephone wiring during a lightning storm.
15. Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
16. Nevertouchuninsulatedtelephonewiresorterminalsunlessthe
telephone line has been disconnected at the network interface.
17. Use caution when installing or modifying telephone lines.
18. This product is intended to be supplied by a Listed Class 2 Direct
Plug-In Power Unit, rated at an output voltage of 9 VDC at 500mA.
19. This product requires AC power in order to operate. In order to
have phone service during a power outage, have another headset
available that is powered only by the communications equipment.
20. Keep all product cords and cables away from operating machinery.
BATTERY PACK PRECAUTIONS
CAUTION: To reduce the risk of fire or injury to persons, read and follow
these instructions.
•Useonlythebatterypacksuppliedwiththisproduct.
•Donotdisposeofbatterypackinare.Thecellsmayexplode.Check
with local codes for possible disposal instructions.
•Donotopenormutilatebatterypack.Releasedelectrolyteiscorrosive
and may cause damage to eyes or skin and may be toxic if swallowed.
•Exercisecareinhandlingthebatterypackinordernotto“short”the
battery contacts with conducting materials such as rings, bracelets,
and keys. The battery or conductor may overheat and cause burns.
•Chargethebatterypackinaccordancewithinstructionssuppliedwith
this unit.
•Observeproperorientationbetweenbatterypackandchargercontacts.
Console Interface Cable 68331-01
6 wire, modular-to-PJ7 cable assembly
Connectors other than the PJ7 are
available upon request
CONTROLS
Name Location Function(s)
Push-to-Talk
(PTT) Button
Remote Keys up the communications radio.
Locking-
Momentary
Selector
Remote Enables or disables locking
operation of the PTT Switch
Audio Link LED
Button
Top of
Remote
Turns the audio link between the
Remote and the Base on and off.
Listen Fine-
Adjust Switch
Remote 1. Adjusts the Listen sensitivity in
2-dB steps.
2. Places the Remote into
Subscription Mode when pressed
and held in either the Up or Down
position.
Listen Coarse-
Adjust Switch
Bottom
of Base
AdjuststheListensensitivityin6-dB
steps.
Talk Volume
Buttons
(fine-adjust)
Top of
Base
1. Adjust the Talk sensitivity in 2-dB
steps.
2 Set the Talk sensitivity to
midrange when both are pressed
quickly at the same time.
3. Place the Base into Subscription
Mode when both are pressed and
held at the same time.
Some versions of the CA12CD-S do
not have these buttons.
Talk Coarse-
Adjust Switch
Bottom
of Base
Adjusts the Talk output for
carbon-, electret-, or dynamic-mic
applications. Carbon (Position 4) is
the factory setting, and is suitable
for most applications.
Subscription
Button
Back of
Base
Places the Base into Subscription
Mode when pressed and held (this
is an alternative to pressing and
holding the Talk Volume buttons).
LEDS
Name Location Function(s)
Audio Link
(green)
Top of
Remote;
part
of the
Audio
Link LED
Button
1) Flashes once per second to
indicate an active audio link.
2) Glows steadily (no flashing) when
the Remote is in Subscription Mode.
3)Flashes6timespersecondifthe
subscription is lost (see the next
section for more information).
Power (green) Base 1) On continuously when the Base is
powered up
2) Flashes once per second
when the Base is in Subscription
Mode.
Talk (green) Base On steadily (no flashing) when PTT
button is depressed.
Charge (orange,
2 ea.)
Base, 1
for each
charging
well
1) Flashes once per second while
the battery is charging.
2) On steadily when the battery is
fully charged.
3) Flashes six times per second to
indicate a fault condition (see the
next section for more information).
SUPPLIES & ACCESSORIES
ATTENTION:
Interruption or termination of the communications link between
the Base and the Remote will occur under the following or similar
conditions:
1. Power outage
2. Moving the Remote out of range from the Base
3. Pressing the Audio Link button on the Remote while the audio link
is active
4. Disconnection of the Base’s power supply
5. Removal of the battery pack from the Remote
6. Lowbattery
7. Operation of other radio devices in the same frequency range
(1.92 to 1.93 GHz for North America and 1.88 to 1.90 GHz for
Europe and some other regions) as the CA12CD-S.
8. Too many CA12CD-Ss in the same location. At least 30 can
typically be operated in the same location. However, this number
can vary depending on such factors as building layout and
materials, physical separation of units, and other radio devices
operating nearby.
ERROR CONDITIONS
If you hear a… It means…
Triple beep YourRemotehaslostitsaudiolinkwith
the Base. Usually, this is due to being too
far away from the Base. (Note that a triple
beep while using the Talk or Listen fine
adjust controls indicates that the level is
at its nominal setting.)
Single beep every
10 seconds
Yourbatteryislowandshouldbe
changed or charged.
If you see… It means…
The Audio Link LED
flashing six times per
second
YourRemoteisnotsubscribedtothe
Base. See the instructions in the next
section for subscribing Bases and
Remotes.
A Charge LED flashing
six times per second
Yourbatteryshouldbereplaced,orthere
could be an object such as a coin or a
paperclip in the charging well.